EAW Steel Picatinny, Sauer 202 Medium (20 MOA)

Introduction

Picatinny rail consists of slots with 5.23 mm spaces between one another, which means that it can be used across its entire length. It is simple to mount and interchangeable – if something is made for a Picatinny rail, it will fit regardless of the manufacturer or manufacturing date. It is affordable, resilient and reliable – this is why it so commonly used by professionals and military. Because of all its great qualities, Picatinny rail has been dominating the rail market in the recent years.

Picatinny is a big step forward from the Weaver standard. Weaver has a few predesignated slots while Picatinny has slots all over its surface, allowing the device to be mounted wherever the user finds it fitting. Weaver's slot is 3.8 mm wide, which is why ring mounts made for a Weaver rail will also fit on a Picatinny rail while ring mounts made specifically for a Picatinny rail will not fit on a Weaver rail. This is one of the main reasons why Picatinny is a far better mounting solution.

EAW is a German company, known for producing top-quality mounts. Their Picatinny rails, which are all made from steel, have a nice finish and come with a unique channel in the middle, allowing the user to clearly see the rifle's sights. Screws are included. EAW chooses only the best materials for their products. All of these great features; however, come at quite a steep price.

20 MOA Inclination

20 MOA inclination is only needed when the scope runs out of elevation. For example, when shooting at the range of 100 m, shooter gains 58.2 cm / 100 m of additional elevation range with a 20 MOA mount. This is approximately 5.8 Mrad of elevation. To make things even clearer – if the target was placed at 100 m, the scope with 20 MOA inclined rail would aim to the center of the target while the rifle’s barrel would aim 58 cm higher than the scope. This gives the shooter extra elevation needed for long range shooting. If you plan to shoot on distances longer than 600 meters, use of rail with 20 MOA is greatly recommended. There is no negative effect of the inclined Picatinny rail in the mounting setup if you only shoot on shorter distances. The same goes also the other way around, since if you don’t shoot on extreme distances then Picatinny rail with inclination is not needed.

About the rifle

Sauer & Sohn was founded in 1751 in Germany. It is the second oldest manufacturer of firearms in the world. One of their most known firearms is Sauer 38H, an advanced semiautomatic pistol that was produced in great numbers – it featured a cocking/decocking lever. They partnered with Swiss company SIG in 1976 – a new line of semi-automatic pistols was launched, branded SIG Sauer.

Sauer 202 Medium, also known as Sauer 202 Standard, is a bolt-action rifle that is chambered for the following calibers: .22-250 Rem., .243 Win., .25-06 Rem., 6,5x55, 6,5x57, .270 Win., 7x64, .308 Win., .30-06, 8x57IS and 9.3x62. Its magazine has 3 rounds. Possible barrel lengths: 510, 560 and 600 mm. There are four holes drilled on Sauer 202's action for mounting purposes, two at the front and two at the rear. The ejection port is located on the right side of the rifle. Bolt runs smoothly and operates silently. The buyer can choose to have the receiver manufactured from aluminium or steel.

Sauer 202 Medium (Standard) has a similar action as Sauer 202 Magnum. The radiuses of the mounting surfaces are the same but there is a difference in B distance (see the picture below). This is why two-piece mounts made for Sauer 202 Medium will fit Sauer 202 Magnum while one-piece mounts made for Sauer 202 Medium will not fit Sauer 202 Magnum.

Sauer 202 Medium (Standard) and Sauer 200 have an action of same dimensions, which is why they share the same mounts.

A: 21.84 mm
B: 94.2 mm
C: 21.84 mm
BHU: 1.5 mm
Fi: 6-48
R1: R17.4
R2: R17.4

Mounting instructions

Remove all the stains (grease, oil etc.) from the rifle's receiver with a cleaning fluid (acetone). Once the surface is clean and dry, check whether the screws match the rail and the holes on the receiver. Make sure that the Picatinny rail is compatible with the rifle by inspecting the mounting holes on both. Before mounting the rail permanently, apply a minimal amount of thread-locking fluid 278 or 648 on screws and contact surfaces. Be careful not to get the fluid in or near the mounting holes. Carefully clean the remaining excess fluid around the rail with a cleaning fluid. Using a torque driver, screw the screws appropriately (up to 2.2 Nm) – do not overtighten.

Warranty

The product has a warranty period of 30 years.