Close

Rifle scopes with mount rail

Sub Categories

Hunting Rifle Scopes
Tactical Rifle Scopes
Target Rifle Scopes
LRF Rifle Scopes
Wide Angle Rifle Scope
Handgun Scopes
Scout Rifle Scopes
Crossbow Scopes
Rifle Scopes Accessories

Introduction

In majority, rifle scopes have central tubular part where rings can be placed for mounting them on a rifle. This is how first scopes were mounted on rifles and it is still common practice in most cases, but not all of them. European manufacturers of rifle scopes have started to produce scopes with special rails under the tubes and this began already decades ago. Such scopes do not need rings for mounting, because they offer completely different solution.

In the beginning, there was only one type of rail in use by most European scope manufacturers. Nevertheless, manufacturers decided to develop better solutions. In the end (we are talking about last decades), three more modern rail standards were established.

This type of mounting systems gained in popularity recently and will become the predominant way of mounting premium scopes in the future.

Pros of Rifle Scopes with Mounting Rails

One of the main advantages of using the rail is that scopes with integrated mounting rail are robust. The whole mount is stiffer because there is lack of many screws which are not needed with this solution. Therefore, reliability comes to place here (also because of the rigidness, mentioned above). If there is no rings attached (with screws) to the scope tube, it also means that there is no stress on the scope – that might also end in better accuracy when shooting. If there is a need to change the scope or put it on the other gun, there will be no marks on the tube from previous installation, which is common when mounting with scope rings.

Schmidt & Bender with S&B convex rail

 

Schmidt & Bender with S&B convex rail

One of the advantages which might be very important to a lot of shooters, is that there is always the perfect level of the scope when rails are used. Balancing and leveling the scope to reach perfect horizontal alignment, while mounting with scope rings, can really be pain in the ass. Through my eyes, always getting the perfect level of the scope, is really the main advantage of using integrated rails. We should not forget that mounting a railed scope is always much easier than with rings. Last, but not least – scopes with integrated mounting rails offers better recoil profness of the mounts.

Cons of Rifle Scopes with Mounting Rails

Sometimes scope bases combined with rifle scope with integrated mounting rails end up much higher, compared to traditional setup with scope rings. Height of our setup must be checked before buying bases and railed scope. In that way, we can avoid disappointment.

As a rule, rail mounting is only available with expensive rifle scopes.

Type of Scopes Rail Standards

Below, we are going to briefly present different types of scope rail standards, available on the market nowadays.

LM Rails

LM rails standard is also known and often called "prism rail" or "70 mm prism". This is the oldest rail standard on the market and is not used anymore. The problem with this standard was that drilling was needed when mounting these scopes on rifles.

Zeiss ZM/VM Rail

ZM/VM rail standard is widely used these days in it is probably the most common rail mounting standard available. It is widely known also as "Inner rail", "M rail" or "Zeiss rail" standard. It was invented by Zeiss and for this reason it is widely known as "Zeiss rail" – however, it is used by many manufacturers nowadays, not only Zeiss.

Zeiss Victory HT 3-12x56 M (rail)

Zeiss Victory HT 3-12x56 M (rail)

Swarovski SR Rail

One of the most famous European optics manufacturer, Swarovski Optik, presented their own mounting rail solution on the market – known as SR rail. It is a specific design, patented by the company. It contains many small teeth under the scope through the whole area of the rail which is great for more powerful calibers with stronger recoil. It is no wonder that this rail is also used by Kahles, since Swarovski company took over Kahles in 1974.

Swarovski Z6i gen.2 2-12x50 BT SR

Swarovski Z6i gen.2 2-12x50 BT SR

S&B Convex Rail

Shmidt & Bender’s Convex rail is made by Schmidt & Bender and is used only by them. In terms of design, it is quite similar to Zeiss rail. However, lower surface on S&B rail rounded and not straight, on the contrary to Zeiss. Comparatively, it is most rare among all rail standards.

Conclusion

As seen above, only the best European rifle scopes manufacturers have rails as option on their scopes. These scopes with rail are usually more expensive as the ones without rails – it is quite logical, because they are more expensive to produce. Unquestionably scopes with rails provide best possible mounting solution and hopefully, most of the rifle scopes in the future will be made with rail mounts.

Show more

Filters
Sort
Items 49-86 of 86
Show
per page
Close
Sort By
Filters
Sort
Items 49-86 of 86
Show
per page
Close
Sort By